Choosing the wrong coring system can be costly. You risk getting poor samples or even damaging equipment. Knowing the real difference between HQ and PQ makes your project successful.
The main difference is size. PQ coring produces a larger diameter core (85 mm) than HQ coring (63.5 mm). This affects sample quality, drilling depth, and equipment compatibility. Choosing the right one depends on your specific project needs, not just which is bigger.

So, we know PQ is bigger than HQ. But that’s just the start of the story. As a supplier, I see many clients get stuck on this point. Let’s break down what these systems really are and how the differences impact your work on the ground. This will help you make a much better choice for your next project.
What Are HQ and PQ Coring Systems?
All the technical names for coring systems can be very confusing. This confusion often leads to buying the wrong tools. Let me explain HQ and PQ in simple terms.
HQ and PQ are standard sizes within the 'Q' wireline coring system. This system lets you retrieve core samples through the drill rods using a cable (wireline). This saves huge amounts of time. The letters, like HQ and PQ, just refer to the specific tool dimensions.

The "Q" in both HQ and PQ stands for the wireline system, which was a huge innovation in drilling. Before wireline, to get a core sample, you had to pull the entire string of drill rods out of the hole. This took hours, especially in deep holes. With a wireline system, the inner tube containing the core sample is pulled up to the surface through the inside of the drill rods using a cable. The outer barrel and rods stay in the hole. This saves a massive amount of time and labor.
A Family of Sizes
HQ and PQ are just two members of a larger family of standardized sizes. The letters represent different dimensions. Think of it like this:
| Size | Hole Diameter (approx.) | Core Diameter (approx.) |
|---|---|---|
| NQ | 75.7 mm | 47.6 mm |
| HQ | 96.0 mm | 63.5 mm |
| PQ | 122.6 mm | 85.0 mm |
This shows that PQ is not just bigger than HQ; it's part of a system designed for different needs. Our factory manufactures all these sizes, and we see how customers use each one for specific tasks.
What are the key differences between HQ and PQ coring?
You know that PQ is bigger than HQ. But what does that really mean for your job? Not knowing these details can cause big problems. Let's compare them more closely.
The key differences are core size (PQ is larger), hole size (PQ is wider), and depth capacity (HQ can typically drill deeper). PQ also requires a more powerful rig, larger drill rods, and has a higher running cost per meter compared to the more versatile HQ system.

The choice between HQ and PQ involves trade-offs. It's not just about getting the biggest sample. Here is a breakdown of how the differences matter in practice.
Size vs. Depth
A PQ system drills a larger hole (around 122.6 mm) to get that big 85 mm core. An HQ system drills a smaller hole (around 96 mm) for a 63.5 mm core. Because the PQ system removes more rock, it requires more torque and power from the drill rig. This also means you generally can't drill as deep with PQ as you can with HQ using the same rig. The smaller HQ system is more efficient for reaching greater depths.
Practical Trade-offs at a Glance
Let's put these differences into a simple table. As a manufacturer, these are the factors I discuss with customers every day when they send us inquiries.
| Feature | HQ Coring | PQ Coring |
|---|---|---|
| Core Diameter | 63.5 mm | 85.0 mm |
| Hole Diameter | 96.0 mm | 122.6 mm |
| Best For | Deeper holes, good rock, cost-efficiency. | Larger samples, fractured rock, shallow depths. |
| Rig Power | Moderate | High |
| Cost | Lower tool and operational cost. | Higher tool and operational cost. |
This shows how every choice has a consequence. A bigger sample from PQ sounds great, but it comes at the cost of depth and requires more powerful, expensive equipment.
How do you choose between HQ and PQ coring?
Choosing the wrong coring system can ruin your project's budget. You could get stuck with useless tools or bad data. Let's make a simple checklist to help you decide.
Choose based on your project goals. Ask these questions: First, what is the minimum core sample size your geologist needs? Second, how deep do you need to drill? Third, what are the ground conditions like? Finally, what are the specifications of your current drill rig?

I often tell my customers that the best tool is the one that fits the job and the equipment you already have. Don't start by asking "HQ or PQ?". Instead, start by answering these four questions about your project.
Question 1: What Core Size Is Required?
Talk to your geologists or engineers first. Sometimes, they need the larger 85 mm PQ core for specific structural tests or to get a good sample from highly fractured rock. But for many exploration projects, the 63.5 mm HQ core is perfectly adequate and more cost-effective to obtain.
Question 2: How Deep Will You Drill?
This is simple physics. A string of PQ rods is heavier and wider than HQ rods. This means more weight for the rig to handle and more friction in the hole. If your target is very deep, the lighter and slimmer HQ system is often the only practical choice.
Question 3: What Is the Rock Like?
In very hard, solid rock, the smaller HQ bit can penetrate faster. In broken, crumbly ground, the larger diameter of the PQ core can sometimes improve core recovery by capturing a more intact sample.
Question 4: What Rig Are You Using?
This is the most important question. Your drill rig has limits on rotation torque, pullback force, and mast height. A PQ system demands more power. Trying to run PQ tools on a rig designed for HQ will lead to slow progress, equipment damage, and frustration. Always check your rig's specifications first.
What are some common misconceptions about HQ vs. PQ coring?
Many myths exist about HQ and PQ coring systems. Believing these myths can cause you to buy the wrong equipment. Let’s correct some of the most common misunderstandings.
A common myth is that PQ is "better" than HQ simply because it's bigger. This is false. The best system is the one that fits your project's depth, geology, and budget. Another misconception is that you can easily swap them. In reality, they require different compatible components.

From my experience talking with buyers from all over the world, a few misunderstandings come up again and again. Clearing these up can save you a lot of trouble.
Misconception: "PQ is always better because the core is bigger."
This is the biggest one. While a large core sample is sometimes necessary, it comes with costs. PQ drilling is slower, consumes more fuel and water, and puts more strain on your rig. For many jobs, the "better" choice is the more efficient HQ system that gets the job done faster and cheaper, while still providing a perfectly good core sample. Efficiency is often more valuable than size.
Misconception: "You can just switch the bit to change sizes."
I sometimes get requests like this. A customer wants to run a PQ bit with their HQ drill rods. This is not possible. The entire system—from the bit and reaming shell to the core barrel and the drill rods—is sized to work together. They are not interchangeable. Trying to mix and match sizes is a recipe for getting tools stuck downhole.
Misconception: "The costs are about the same."
This is also not true. PQ consumables—the bits, shells, and core lifters—are larger and contain more materials, so they cost more. The bigger equipment also means higher shipping costs from our factory to your site. Over the course of a long project, these costs add up significantly.
What should you consider before purchasing HQ or PQ coring equipment?
Buying new coring equipment is a big decision. One small mistake on your purchase order can become a huge, expensive problem. Here is a final checklist before you buy.
Before buying, confirm everything is compatible with your rig and current drill rods. Think about the total cost, including consumables and shipping, not just the initial price. Most importantly, talk to your supplier. Give them your project details so they can help you choose correctly.

As a manufacturer, my goal is for you to be successful with our tools. An order for the wrong parts doesn't help anyone. So before you click "buy" or send that PO, please think about these practical points.
Confirm Your Existing Equipment
This is the most common point of failure. You must know the exact specifications of your drill rig and drill rods. What is the thread type on your rods? What is your rig's maximum torque and pullback capacity? A good supplier will ask these questions. Be ready with the answers. A photo of your current rod thread can be very helpful.
Think Beyond the Price Tag
Don't just compare the price of an HQ bit to a PQ bit. Think about the Total Cost of Ownership. PQ might mean slower progress, more fuel, and more wear on your expensive drill rig. Sometimes, the cheaper-per-meter HQ system is the more profitable choice overall.
Partner with Your Supplier
Don't see your supplier as just a vendor. See us as a partner. We have seen thousands of orders and have helped customers avoid common mistakes. Share the details of your project: the target depth, the type of rock, the equipment you are using. The more information you give us, the better we can help you select the exact tools you need for a successful project. This kind of conversation before a purchase is the best way to avoid problems later.
Conclusion
In the end, choosing between HQ and PQ is not about which is better. It is about matching the right tool to your specific geology, depth, and rig for success.Need Help Choosing?
GET QUOTE







