Two benches, same granite, same crew size. One rig drills a 115 mm hole in four minutes, the other takes nine and burns through two bits a shift. No crew made a mistake. The issue is habit-driven tool selection: old hammer-drilling mindsets get carried over to rotary rigs, and the bit takes the blame.
Rotary drilling cuts rock with weight on bit and rotation, and wins in soft to medium ground and large holes. Percussive drilling breaks rock with impact plus rotation, and wins in hard, competent rock, in deep straight holes, and in small diameters.

Speed and price are the two questions buyers ask first. Neither one has an answer until the ground and the rig are on the table.
Which Drilling Method Drills Faster in Your Ground?
Rotary cuts. Percussive breaks. That is the whole difference, and everything else follows from it.
A rotary bit is pressed into the rock and turned. A tricone rolls and crushes. A PDC shears. A drag bit scrapes. The bit needs weight on it, and it needs the cuttings cleared away from the face. A percussive bit is hit. A piston sends impact energy into the rock, and the rock gives up in fatigue, crack by crack. Top hammer sends that energy down the rod. DTH puts the hammer at the bottom, right behind the bit, so the energy arrives whole.
In soft to medium ground, rotary is the faster method, provided the rig can put weight on the bit. In hard, competent rock, impact wins. A 115 mm DTH hammer on 24 bar will run 15 to 25 m/h in granite. A 200 mm tricone in the same rock runs 4 to 8, and the cones are done in 300 meters. The diameters differ there, and so does the area of rock under the tool: 115 mm covers about a third of the face a 200 mm bit works on. Read the gap as a direction, not as a like-for-like rate.

Speed is a system number, not a bit number
When a buyer asks which method is faster, I do not quote a penetration rate. I ask what the rock does under the tool.
Soft overburden is rotary ground. Cutting and scraping hold a steady rate, and impact adds nothing except an air bill. Medium rock is a contest: a tricone or PDC holds rate until hardness climbs, then the hammer starts to pull ahead. Hard, competent rock belongs to impact, because the blow fractures the face before rotation indexes the buttons to a fresh spot. Fractured ground is its own problem. There the bit choice matters less than whether the hole will hold air and whether the cuttings can get out of it. And big blast holes pull the decision toward the rig rather than the rock, because pull-down force and bit size decide what is physically possible.
Hole cleaning is the part buyers skip. A fast bit turns slow the moment cuttings pile up at the face and get reground. Rotary systems clear with air, mud or water depending on the job. DTH lives or dies on air volume and pressure. If the compressor cannot power the hammer and lift the cuttings at the same time, the whole system loses rate, and the bit gets blamed for it.
One more thing on speed. The method that wins on one bench can lose on the next. A contractor in hard granite moves to DTH, then hits a weathered zone at 20 meters and finds the hammer blowing air into a hole that will not hold it. The method did not fail. The ground changed, and nobody re-checked.
What Is the Real Cost Gap Between Rotary and Percussive Drilling?
Cost problems show up after the purchase order, not before it. The quote has one line. The site has five.
The gap between the two methods is cost per meter, not price per bit. A cheap bit that drills 350 meters costs more than an expensive one that drills 900, and neither number appears on the invoice.

One worked example, and the numbers that flip it
A 152 mm hole in granite, rig and crew at USD 150 an hour. These are figures close to what I have seen on real tenders.
| Line item | Tricone, granite | DTH, granite |
|---|---|---|
| Bit price | USD 1,500 | USD 900 |
| Bit life | 350 m | 700 m |
| Bit cost per meter | 4.29 | 1.29 |
| Penetration rate | 6 m/h | 18 m/h |
| Rig cost per meter | 25.00 | 8.33 |
| Total per meter | 29.29 | 9.62 |
The bit is the small line. Rig hours are the big one, and they are decided by penetration rate. That is why a bit that costs two-thirds more can still be the cheaper meter.
Now move the same hole to 200 mm limestone, same rig rate and the same tricone price of USD 1,500. The tricone runs 25 m/h and lasts 1,500 meters, so it carries USD 1.00 of bit and USD 6.00 of rig hour, and lands near USD 7.00 a meter. The hammer runs 22 m/h and lasts 900 meters; at USD 900 a bit it carries USD 1.00 of bit, USD 6.82 of rig hour and about USD 0.22 of air and compressor wear, so it lands near USD 8.04. The ranking flips. In soft rock the hammer is paying for air it does not need, and the tricone is the cheaper meter.
Your rock will move these numbers. The method of counting them is what matters.
What the quote leaves out
Visible costs are easy. Bit, hammer, rods, adapters, compressor, fuel, freight, spares. Hidden costs are the ones that break a budget. A bit change on a deep rotary hole is two to four hours of a stopped rig. A stuck string is a fishing job, and a fishing job is a shift. A hole drilled off pattern is a re-drill or a bad blast. An undersized compressor is not a breakdown, so nobody logs it, and it costs money every hour.
A rig and crew standing still runs USD 150 to 250 an hour on most sites I have visited. Three hours of downtime costs more than the difference between a good bit and a cheap one. That is the comparison a buyer should be making.
Ranking Bit quotes on drawings and rock data, not on a price list. Send the hole spec and the rig model, and the answer comes back as a setup, not a part number.
How Do Rock Conditions Decide Between Tricone and DTH Bits?
Rock does not punish the wrong method. It punishes the wrong bit, and it does it fast.
Hardness is not the only variable. Abrasiveness, fractures, water and hole diameter change the answer, and a formation can be easy to break and brutal to wear.

What each bit is actually doing down there
A tricone carries three rolling cones with milled teeth or tungsten carbide inserts. The cones roll on the bottom and break rock by crushing, chipping and gouging. The IADC code tells you the formation the bit was built for, from soft to hard to abrasive. A bit built for soft shale will not last an hour in granite, no matter how much weight you put on it.
A DTH bit carries carbide buttons and takes a direct hit from the piston. Rotation only indexes the buttons so each blow lands on fresh rock. Button grade, face design and gauge protection do the work. In hard, competent ground this is the most efficient way to break rock that exists.
Soft to medium ground is tricone country, and the only thing worth watching is bearing life. Hard and competent ground usually belongs to the hammer on meter rate. Abrasive formations do not care which method you picked, they attack whichever part touches rock, so cutter and bearing protection matter on one side and button grade and gauge protection on the other. Fractured ground is where DTH gets expensive, because air escapes through the cracks instead of lifting cuttings. Mixed layers break the logic entirely. One bit cannot suit every layer, so you either accept a compromise or you plan a bit change at the contact.
The two numbers that decide it
Weight on bit. A 152 mm tricone wants roughly 40 to 70 kN, with the top of that range for hard, abrasive formation. If the rig cannot hold 40 at the bit, the bit does not cut, it polishes, and the buyer concludes the bit is soft. It is not soft. It is under-loaded.
Air. A 152 mm DTH hammer wants 15 to 18 m³/min at 24 bar, and it wants that pressure at the hammer, not at the compressor outlet. Hose length, leaks and altitude all eat into it. A hammer run at 16 bar instead of 24 hits softer, cycles slower, and wears its buttons in a way that looks like a manufacturing fault.
Before recommending a bit, I ask for the rock description, the hole size and depth, the rig model, the compressor data if it is DTH, and photos of the last bits that came out. Worn bit photos tell me more than a geological report. They show what the tool actually met.
The question is not tricone or DTH. It is which bit breaks this rock at a rate your rig can support.
Which Tool Mistakes Blow Up Your Drilling Budget?
Most of these are decided in an email, months before anyone sees the rock.
The expensive mistakes are boring ones: buying on price, ignoring abrasiveness, mismatching the thread, and running a hammer on air it was never designed for.

Price is not a specification
A low price is fine when the tool suits the job. The problem is that the tool and the job are rarely compared before the order. Two bits with the same part number can hold the same drawing and still differ in carbide grade, sintering cycle and hardfacing thickness. That is why the second batch behaves differently from the first, and why the buyer starts to distrust the method instead of the supplier.
Abrasiveness gets ignored more than hardness. A formation does not have to be hard to destroy a bit. Sandstone with high quartz content will wear a cutter flat at a rate that surprises people who only asked "is it hard rock?"
Thread mismatch is the fastest way to stop a job. Rods, adapters, subs, hammers and bits have to line up. A wrong connection is not a delay of hours, it is a delay until the right part arrives.
Read the wear before you reorder
Wear is a report card. It tells you what went wrong before the bit failed.
| What you see on the bit | What it usually means | What to change |
|---|---|---|
| Buttons cracked or flattened on a DTH bit | Air pressure short at the hammer | Measure at the hammer, not at the gauge |
| Buttons sheared off, holes in the face | Bit run past its wear limit, or overblowing | Pull on meters, not on feel |
| Steel washed between buttons | Not enough air volume, cuttings grinding the body | Check nozzle and face design |
| Gauge worn, bit out of round | Too much rpm, or a worn stabilizer | Slow the rotation, check the string |
| Tricone teeth flat, bearings seized | Weight on bit too high, cuttings not cleared | Reduce weight, increase flushing |
| Face balled up with clay | Wrong flushing for the ground | Change the medium, not the bit |
| Hole drifting off pattern | Top hammer too deep, or too little weight on a rotary string | Move to DTH, stiffen the string |
If the same failure shows up twice, the bit is not the problem. The setup is. Reordering the same part with the same parameters gets you the same result at a higher price.
One more, and it is the cheapest to fix. Spares. A mine that holds no standby bit is one worn button away from an idle shift, and the emergency order always costs more than the stock would have.
What Checklist Picks the Right Drill Setup for Your Mine?
A setup goes wrong when one factor decides it. Rock hardness alone is not enough. Price alone is not enough. Rig brand alone is not enough.
Start with the hole, not the tool. Diameter, depth, straightness and meters per shift narrow the method before price enters the conversation.

The checklist I use on a first call
Run it in order and most of the arguments disappear.
- Define the hole. Diameter, depth, straightness tolerance, meters per shift. A blast hole, a water well and a geotech hole have three different tolerances, and that alone can rule a method out.
- Describe the rock. Type, hardness, abrasiveness, fractures, water. Send photos of worn bits if you have them.
- Check what you already own. Pull-down force, torque and rotation range on the rig. Pressure and volume at the hammer on the compressor. A method your equipment cannot support is not a method, it is a purchase.
- Pick the bit family. Tricone, PDC, drag or DTH, matched to the formation and the hole.
- Confirm the string. Rods, adapters, subs, threads, hammer size. This is where cheap orders die.
- Count the meter. Bit, rig hour, downtime, freight. Then add lead time and spare stock, because a low price loses its value the day the rig waits for a container.
The last step is the one that changes behavior. Once a mine has three months of meter logs, the next order stops being an argument about unit price and becomes a decision with a number behind it.
Frequently Asked Questions
Is rotary drilling faster than percussive drilling?
Only in soft to medium ground, and only when the rig can hold weight on the bit. In hard, competent rock the hammer wins on meter rate, because the impact fractures the face before rotation indexes the buttons to a fresh spot.
Can a tricone bit drill hard granite?
Yes, but not economically. A 200 mm tricone in granite runs 4 to 8 m/h and is usually spent inside 300 meters, so bit cost per meter climbs while rig hours stay high.
What air pressure does a 152 mm DTH hammer need?
Roughly 15 to 18 m³/min at 24 bar, and that pressure has to arrive at the hammer, not at the compressor outlet. Hose length, leaks and altitude all take a share of it.
Why does my bit wear out faster than the quoted life?
Four causes cover most of it: too little weight on bit, short air pressure at the hammer, cuttings not cleared from the face, and a bit built for the wrong formation. Read the wear pattern before you reorder.
Conclusion
Rotary drilling vs percussive drilling in mining has no permanent winner. Match the method to the rock, the hole and the rig. Count the meter, not the bit. Read the wear before you reorder. Send Ranking Bit your hole spec and rig data, and we will review the setup before you commit to a container.Need Help Choosing?
GET QUOTE









